Mezzanine Goods Floor Lifter, Aston Martin Lagonda Limited Goods Lift


Mezzanine Goods Floor Lift

Typical overview of the Mezzanine floor lifter: The lift will be constructed using a single mast which must be bolted to the building block-work to provide additional support to the load legs. The lift platform will measure approximately 2140mm wide by 1540mm deep and will close down over the legs. The platform will feature 1100mm high rails on all sides and a double outwards opening gate. The gates will be spring loaded and will lock with a gravity system but will also be sensed to prevent platform movement if the gate is open. For more information on this range of products please contact us or call 01553 811977.

Goods Lift Drawing for Aston Martin Lagonda Limited.pdf

 

General features and advantages of the Mezzanine Floor Lifter:

Design, manufacture and install 1 off mast-type goods lift to be installed alongside a mezzanine floor system for Aston Martin Lagonda Limited

The lift will be constructed using a single mast which must be bolted down to the ground floor as well as the block work wall to the left of the mezzanine. Brackets will be supplied to support the mast rigidly away from the structural building brace.

(Dimensions to be confirmed during pre-manufacture site survey)

The lift platform will measure approximately 2200mm wide by 1600mm deep and will close down over the legs

The clear working platform area will be 2140mm x 1540mm

The overall plan size of the lift will be approx 2200mm wide x 1850mm deep The platform will feature 1100mm high rails on all sides with twin outwards opening gates opposite the mast (Side B) and to the left of the mast (Side A) The gates will lock with a gravity system but will also be sensed to prevent platform movement if the gate is open.
The platform will close to the floor with a 60mm lowered height and have a total raised height of 3460mm

The maximum lift height will be governed by a limit switch system to ensure that the platform parks with the mezzanine upper floor.

The platform will be supplied with a loading ramp to be permanently fixed to the ground floor measuring 2200mm wide by 600mm long giving a gradient of 10%. Mounted opposite the mast (Side B)
The hydraulic power pack will be mounted to the mast and electrical system will be housed in a separate box, mounted on the enclosure at ground level.

Control points will be positioned at both ground and upper floor levels. Both points will feature latching call buttons and emergency stop controls.

Power requirement: 415V 3 phase + Neutral via 10amp isolator

(Supplied by customer install location TBC)

Motor specification: 0.8Kw 3phase 415V with 4ltr reservoir

Maximum lift capacity will be 200Kg


Manufacture and install 1 off External guard system for both upper and lower floors

The lift will be supplied with an external guard to fully enclose the unit and will comprise as follows:

5660mm high mesh panels on 3 exposed sides incorporating twin outward opening gates 2000mm high opposite the mast (Side B) at ground level and twin outward opening gates 2000mm high to the left of the mast (Side A). The gates will be fitted with an electrical interlock to prevent opening when the lift is not parked.

The enclosure will reach under the mezzanine at ground level by 200mm with panels 2500mm high. At mezzanine level the enclosure height will be 2200mm again reaching in 200mm. This is to allow appropriate clearance between the outside face of the enclosure and the moving lift car

Overall size of enclosure 2600mm x 2050mm

Installation:

Installation of the lift at: Aston Martin Lagonda Limited,

Banbury Road,

Gaydon,

Warwick.

CV35 ODB

We estimate that this installation will take two installers, a maximum of 4 days for completion.


Delivery:

The unit will be delivered the day before installation is scheduled.

Section A - Height

MHS


Code

Dimension

Notes

Floor Height

H

3455

Ground floor to first floor level

Under Ceiling Height

E

N\A

Ground to under ceiling height

Mast Height

H1

4105


Platform rail height

D

1100

Standard rail height is 1100mm

Section B – Foot-print & gates
Aston Martin


Code

Dimension

Notes

PLATFORM




Platform Width

(Overall lift width)

B

2200


Platform Length

C

1600


Useable Platform Width

B1

2140


Useable Platform Length

C1

1540


Overall lift Length

F

1850



ENCLOSURE




Enclosure Length

X

2050


Enclosure Width

Y

2600


Enclosure Height (Ground floor)


2500


Enclosure Height (1st Floor


2200


Enclosure (Other details)

3 sided enclosure full height on 2 sides split by mezz on remaining side overall height 5660mm

In some applications the enclosure may be full height against the side of a mezzanine

Side

Platform

Gate

Enclosure Gate (ground floor)

Enclosure Gate (1st floor)

Ramp

Single

Twin

Single

Twin

Single

Twin

A


YES




YES


B


YES


YES



YES

C








Support


Details

Notes

Wall Mount


Wall mounted but is needs to be offset from the wall to avoid a building brace

Please give details of the walling materials

Through Mezzanine



Through mezzanine applications require details of the mezzanine structure to ascertain whether or not appropriate support is available

Other



Please provide details

Voltage


Notes

240v Single Phase



110v Single Phase



415v Three Phase

YES

Standard fit

Lift Colour

RAL 9010 Pure White

Standard RAL5017 (Blue)

Enclosure colour

RAL 9010 Pure White

Standard RAL7037 (Grey)

Anti-slip protection

none

None as standard

See more examples... 1 | 2 | 3 | 4 | 5 | 6 | 7| 8 | 9 | 10 | 11 | 12 | 13 | 14 | 15 | 16 | 17 | 18 | 19 | 20 | 21 |

Mezzanine Floor Enquiry Form

Product Downloads

MHS Solutions Range.pdf

Mezzanine Floor Lifter.pdf

 
Contact us on Tel 01553 811977 / Fax 01553 811004 or email us at sales@manualhandlingsolutions.co.uk
 
Mezzanine Goods Floor Lift