Mezzanine Goods Floor Lifter, Manual Handling Solutions Goods Lift


Mezzanine Goods Floor Lift

Typical overview of the Mezzanine Goods lifter: The lift will be constructed using a single mast which must be bolted to the building block-work to provide additional support to the load legs. The lift platform will measure approximately 1500mm wide by 1500mm deep and will close down over the legs. The platform will feature 1100mm high rails on all sides and a single outwards opening gate on the right-hand side of the mast. The gate will be spring loaded and will lock with a gravity system but will also be sensed to prevent platform movement if the gate is open. For more information on this range of products please contact us or call 01553 811977
 

Design, manufacture and install 1 off mast-type goods lift to be installed through a mezzanine floor system up against an

  • The lift will be constructed using a single mast which must be bolted down to the ground floor.
  • The lift platform will measure approximately 1060mm wide by 1500mm deep and will close down over the legs
  • The clear working platform area will be 1200mm x 1440mm
  • The overall plan size of the lift will be approx 1660mm wide x 1940mm deep including the enclosure

The distance from the loading end of the mezzanine to the far side of the enclosure will be 1460mm and will therefore extend out into the gang-way by 195mm

  • The platform will feature 1100mm high rails on all sides and a twin outwards opening gate on Side A. The gates will lock with a gravity system but will also be sensed to prevent platform movement if the gate is open.
  • The platform will close to the floor with a 60mm lowered height and have a total raised height of 3300mm
  • The maximum lift height will be governed by a limit switch system to ensure that the platform parks with the mezzanine upper floor.
  • The platform will be supplied with a loading ramp to be permanently fixed to the ground floor measuring 1500mm wide by 900mm long giving a gradient of 15%. Mounted on Side A
  • The hydraulic power pack will be mounted to the mast and electrical system will be housed in a separate wall mounted box at ground level.
  • Control points will be positioned at both ground and upper floor levels. Both points will feature latching call buttons and emergency stop controls.
  • Power requirement: 415V 3 phase + Neutral via 10amp isolator (Supplied by customer)
  • Motor specification: 0.8Kw 3phase 415V with 4ltr reservoir
  • Maximum lift capacity will be 500Kg
  •  

Manufacture and install 1 off External guard system for both upper and lower floors

  • The lift will be supplied with an external guard to fully enclose the unit over the full stroke and will comprise as follows:
  • Ground Floor: 2500mm high mesh panels on three sides with a twin out-ward opening gate 2100mm high on Side A. The gate will be fitted with an electrical interlock to prevent opening when the lift is not parked.
  • First Floor: 2200mm high mesh panels on three sides with a twin out-ward opening gate 2100mm on side A. The gate will be fitted with an electrical interlock to prevent opening when the lift is not parked.
  • The enclosure will be full height to 5500mm on sides B and C
  • The enclosure will also be fitted with a panel to bridge the gap between the end of the back wall and the outside of the enclosure.
  •  
  • Installation:

Installation of the lift at:                         Newark Road, Peterborough

We estimate that this installation will take two installers, a maximum of 4 days for completion.

Delivery:

Please provide drawings/ information on the location of the lift within the premises so that we can assess whether or not there are any special requirements for getting the unit into position.
The unit will be delivered the day before installation is scheduled.

Section A - Heights
MHS


Code

Dimension

Notes

Floor Height

H

3300

Ground floor to first floor level

Under Ceiling Height

E

2900

Ground to under ceiling height

Mast Height

H1

3745

This is equal to H + 445mm

Platform rail height

D

1100

Standard rail height is 1100mm

Section B – Foot-print & gates
Aston Martin


Code

Dimension

Notes

PLATFORM




Platform Width

(Overall lift width)

B

1260


Platform Length

C

1500


Useable Platform Width

B1

1200


Useable Platform Length

C1

1440


Overall lift Length

F

1740



ENCLOSURE




Enclosure Length

X

1940


Enclosure Width

Y

1660


Enclosure Height (Ground floor)


-


Enclosure Height (1st Floor


2200


Enclosure (Other details)

The enclosure will be full height on sides B and C to 5500mm.

At 1st floor level to 2200mm and under mezz on side A to 2500mm

In some applications the enclosure may be full height against the side of a mezzanine

Side

Platform

Gate

Enclosure Gate (ground floor)

Enclosure Gate (1st floor)

Ramp

Single

Twin

Single

Twin

Single

Twin

A


YES


YES


YES

YES

B


 


 



 

C








Support


Details

Notes

Wall Mount


Wall mounted - to 3000mm block-work wall

Please give details of the walling materials

Through Mezzanine



Through mezzanine applications require details of the mezzanine structure to ascertain whether or not appropriate support is available

Other



Please provide details

Voltage


Notes

240v Single Phase



110v Single Phase



415v Three Phase

YES

Standard fit

Lift Colour

RAL 5017

Standard RAL5017 (Blue)

Enclosure colour

RAL 7037

Standard RAL7037 (Grey)

Anti-slip protection

none

None as standard

See more examples... 1 | 2 | 3 | 4 | 5 | 6 | 7| 8 | 9 | 10 | 11 | 12 | 13 | 14 | 15 | 16 | 17 | 18 | 19 | 20 | 21 |

Mezzanine Floor Enquiry Form

Product Downloads

MHS Solutions Range.pdf

Mezzanine Floor Lifter.pdf

 
Contact us on Tel 01553 811977 / Fax 01553 811004 or email us at sales@manualhandlingsolutions.co.uk
 
Mezzanine Goods Floor Lift